Albumin suppresses oxidation of TiNb alloy in the simulated inflammatory environment.

Literature data has shown that reactive oxygen species (ROS), generated by immune cells during post-operative inflammation, could induce corrosion of standard Ti-based biomaterials. For Ti6Al4V alloy, this process can be further accelerated by the presence of albumin. However, this phenomenon remains unexplored for Ti ß-phase materials, such as TiNb alloys. These alloys are attractive due to their relatively low elastic modulus value. This study aims to address the question of how albumin influences the corrosion resistance of TiNb alloy under simulated inflammation. Electrochemical and ion release tests have revealed that albumin significantly enhances corrosion resistance over both short (2 and 24 h) and long (2 weeks) exposure periods. Furthermore, post-immersion XPS and cross-section TEM analysis have demonstrated that prolonged exposure to an albumin-rich inflammatory solution results in the complete coverage of the TiNb surface by a protein layer. Moreover, TEM studies revealed that H2O2-induced oxidation and further formation of a defective oxide film were suppressed in the solution enriched with albumin. Overall results indicate that contrary to Ti6Al4V, the addition of albumin to the PBS + H2O2 solution is not necessary to simulate the harsh inflammatory conditions as could possibly be found in the vicinity of a TiNb implant.

Bridgman-Grown (Cd,Mn)Te and (Cd,Mn)(Te,Se): A Comparison of Suitability for X and Gamma Detectors.

This study explores the suitability of (Cd,Mn)Te and (Cd,Mn)(Te,Se) as room-temperature X-ray and gamma-ray detector materials, grown using the Bridgman method. The investigation compares their crystal structure, mechanical and optical properties, and radiation detection capabilities. Both crystals can yield large-area single crystal samples measuring approximately 30 × 30 mm2. In low-temperature photoluminescence analysis, both materials showed defect states, and annealing in cadmium vapors effectively eliminated donor-acceptor pair luminescence in (Cd,Mn)Te but not in (Cd,Mn)(Te,Se). Moreover, harder (Cd,Mn)(Te,Se) exhibited a higher etch pit density compared to softer (Cd,Mn)Te. X-ray diffraction examination revealed uniform lattice constant distribution in both compounds, with variations at a part per million level. (Cd,Mn)Te crystals demonstrated excellent single crystal properties with narrower omega scan widths, while (Cd,Mn)(Te,Se) exhibited a high contribution of block-like structures with significantly larger misorientation angles. Spectroscopic evaluations revealed better performance of a pixelated (Cd,Mn)Te detector, in comparison to (Cd,Mn)(Te,Se), achieving a mean full width at half maximum of 14% for the 122 keV gamma peak of Co-57. The reduced performance of the (Cd,Mn)(Te,Se) detector may be attributed to deep trap-related luminescence or block-like structures with larger misorientation angles. In conclusion, Bridgman-grown (Cd,Mn)Te emerges as a more promising material for X-ray and gamma-ray detectors when compared to (Cd,Mn)(Te,Se).

Comparison of Microstructure, Texture, and Mechanical Properties of TZ61 and AZ61 Mg Alloys Processed by Differential Speed Rolling.

In this work, the comparison of microstructure, texture, and mechanical properties of the newly developed TZ61 (Mg-6Sn-1Zn) alloy with the commercially available AZ61 (Mg-6Al-1Zn) has been presented. Both analyzed Mg alloys were processed by conventional symmetric and asymmetric rolling (i.e., Differential Speed Rolling-DSR). The microstructure and texture were examined by EBSD and XRD, whereas the mechanical behavior was investigated by uniaxial tensile tests. DSR processing led to more effective grain refinement of both TZ61 and AZ61 sheets. However, a high fraction of Mg2Sn phase precipitates in the TZ61 sheets hindered grain growth what resulted in their smaller grain size as compared to AZ61 sheets. DSR processing lowered also the basal texture intensity in the TZ61 and AZ61 sheets. A unique basal poles splitting was observed for the as-rolled TZ61 alloy, while AZ61 alloy exhibited a typical single-peak basal texture. Finally, the reduced grain size and weakened basal texture by DSR processing caused increase of plasticity of the annealed TZ61 and AZ61 sheets. Nevertheless, the annealed AZ61 sheets showed higher uniform elongation and strength (as compared to TZ61 ones), which has been attributed to their significantly lower texture intensity and greater ability to strain hardening.

Microstructure, Texture and Mechanical Properties of Mg-6Sn Alloy Processed by Differential Speed Rolling.

The effect of shear deformation introduced by differential speed rolling (DSR) on the microstructure, texture and mechanical properties of Mg-6Sn alloy was investigated. Mg-6Sn sheets were obtained by DSR at speed ratio between upper and lower rolls of R = 1, 1.25, 2 and 3 (R = 1 refers to symmetric rolling). The microstructural and textural changes were investigated by electron backscattered diffraction (EBSD) and XRD, while the mechanical performance was evaluated based on tensile tests and calculated Lankford parameters. DSR resulted in the pronounced grain refinement of Mg-6Sn sheets and spreading of basal texture as compared to conventionally rolled one. The average grain size and basal texture intensity gradually decreased with increasing speed ratio. The basal poles splitting to transverse direction (TD) or rolling direction (RD) was observed for all Mg-6Sn sheets. For the as-rolled sheets, YS and UTS increased with increasing speed ratio, but a significant anisotropy of strength and ductility between RD and TD has been observed. After annealing at 300 °C, Mg-6Sn sheets became more homogeneous, and the elongation to failure was increased with higher speed ratios. Moreover, the annealed Mg-6Sn sheets were characterized by a very low normal anisotropy (0.91-1.16), which is normally not achieved for the most common Mg-Al-Zn alloys.

Mechanical properties, structural and texture evolution of biocompatible Ti-45Nb alloy processed by severe plastic deformation.

Biocompatible ß Ti-45Nb (wt%) alloys were subjected to different methods of severe plastic deformation (SPD) in order to increase the mechanical strength without increasing the low Young׳s modulus thus avoiding the stress shielding effect. The mechanical properties, microstructural changes and texture evolution were investigated, by means of tensile, microhardness and nanoindentation tests, as well as TEM and XRD. Significant increases of hardness and ultimate tensile strength up to a factor 1.6 and 2, respectively, could be achieved depending on the SPD method applied (hydrostatic extrusion - HE, high pressure torsion - HPT, and rolling and folding - R&F), while maintaining the considerable ductility. Due to the high content of ß-stabilizing Nb, the initial lattice structure turned out to be stable upon all of the SPD methods applied. This explains why with all SPD methods the apparent Young׳s modulus measured by nanoindentation did not exceed that of the non-processed material. For its variations below that level, they could be quantitatively related to changes in the SPD-induced texture, by means of calculations of the Young׳s modulus on basis of the texture data which were carefully measured for all different SPD techniques and strains. This is especially true for the significant decrease of Young׳s modulus for increasing R&F processing which is thus identified as a texture effect. Considering the mechanical biocompatibility (percentage of hardness over Young׳s modulus), a value of 3-4% is achieved with all the SPD routes applied which recommends them for enhancing ß Ti-alloys for biomedical applications.